ElectroDroid Apps

Software ini merupakan koleksi yang sangat powerful untuk alat electronik dan sebagai referensi. Jika anda sangat tertarik dengan elektronik anda wajib menginstall software ini. 

ElectroDroid ini sangat simple dan powerful. Didalamnya terdapat berbagai refernsi antara lain:

• Resistor color code decoder (3-6 bands);
• Inductor color code decoder;
• Ohm’s law calculator;
• Reactance calculator;
• Voltage divider;
• Resistor ratio, value/series/parallel;
• Capacitor charge calculation;
• Operational amplifier;
• LED resistor calculator;
• LM317 calculator;
• Heat dissipation;
• Battery Life calculator;
• Inductor design tool;
• Voltage Drop calculator;
• PCB Trace Width calculator;
• Simple Filters calculator;
• NE555 astable calculator;
• Port pin-out (USB, Serial, Parallel, Ethernet, SCART, DVI, HDMI, S-Video, VGA, FireWire, Jack, XLR, RCA, DMX, ATX, Molex, EIDE, SATA);
• Resources (Resistivity table; Table of standard resistors and capacitors; Capacitor marking codes; AWG and SWG Wire size; Ampacity Table; Symbols and Abbreviations; Circuit Schematic Symbols; SI Units prefixes; Battery info; Boolean logic gate and algebra Theorems; 7400 info and pinout; ASCII code);
• Full support for EIA resistor series for all caluculators;
...and more to come!

Untuk versi full silahkan anda cek di http://electrodroid.demisoft.it

Berikut tampilan softwarenya di SmartPhone Android.

Semoga bermanfaat.

Read More

Reliable Protection of 24 VDC Load Circuits

When overloads and short circuits occur, there’s always a tradeoff between the power supply shutting down the entire 24 VDC supply and keeping load circuits that aren’t impacted by the failure continuing to run. The new SITOP PSE200U electronic diagnostic module from Siemens Industry Automation Division constantly monitors up to four 24 VDC load circuits for overloads and short circuits.

“Today’s switched-mode power supplies provide advanced functionality, by protecting 24 VDC loads against any kinds of overload. Unfortunately, it responds by shutting down the power supply to all load circuits even before a fuse or circuit breaker can trip on the circuit that is actually being overloaded. The result: Power is shut down to all 24 VDC load circuits, even those that aren’t affected,” says Kai Bronzel, product marketing manger, Siemens Industry. “The SITOP PSE200U electronic diagnostic module intelligently shuts down the current to the affected load circuit, without impacting the other load circuits that don’t have problems.” Furthermore, the SITOP PSE200U provides for sequential start up, which significantly reduces the total current required from the power supply during the start up phase of high inrush loads. This avoids the shutdown of the power supply when the total inrush current exceeds the current limitation of the power supply.
In order to more closely match the application, there are now two versions of the device with tripping current ranges of 0.5 to 3 and 3 to 10 amperes available. This is an improvement over the previous SITOP select model, which had a wide adjustment tripping current range of 2 to 10 amperes. Used as an additional component in switched mode regulated 24 VDC power supplies, the new SITOP PSE200U electronic diagnostic module detects not only slight overloads but also “creeping” short circuits on high-resistance cables. If an overload or short circuit occurs, the device switches off the current to the faulty path. This prevents the power supply voltage from dipping, thus ensuring that power continues to be supplied to all the other circuits not affected by the fault. Up to four load circuits per module can be protected. Additional electronic diagnostic modules can be connected to the power supply if the application requires the protection of more circuits.
The new SITOP PSE200U electronic diagnostic module has sealable potentiometer covers to protect the set tripping currents against unwanted changes. The three-color LED and signaling contact concept makes it simple to troubleshoot systems and get directly to the faults. Diagnostics data can be transmitted to a higher-level controller for remote diagnostics. The SITOP PSE200U allows fast commissioning due to switch on/off functionality by using individual reset buttons per circuit in front of the unit. In addition a remote reset from a higher level control system is also possible. In contrast to conventional miniature circuit breakers, which do not trip until the current rises to a multiple of the rated current, this new electronic diagnostic module already responds to an overload that is only slightly above the set tripping current. The device also differentiates between a sustained fault and a transitory, operational overcurrent. This enables short circuits to be detected even on high-resistance cables in which, for example, core cross-sections are small or there is a long distance to the load.

Click here for more information on SITOP PSE200U electronic diagnostic module.

Read More

Bridging Profibus and Modbus-TCP networks with an Anybus X-gateway

Simple to use intelligent Gateway connects Schneider Electric, ABB or GE PLC’s with Siemens automation systems and networks.

The Anybus X-gateway from HMS Industrial Networks enables system integrators to easily transfer I/O data between two different PLC systems and networks. The X-gateway is a configurable stand-alone gateway that allows plant-floor devices on a Profibus network to communicate with the devices on a Modbus-TCP network and vice versa. Typical applications are installations with mixed usage of Siemens and Schneider Electric, ABB or GE PLCs. One example is automobile manufacturing plants where Profibus based segments shall be integrated into industrial Ethernet based control applications with the popular Modbus-TCP protocol.

The X-gateway is a compact device for standard DIN rail mounting and 24 Volt industrial power supply. It functions as a server (slave) on the Modbus-TCP network and as a master on the Profibus side. The Profibus master functionality is configured with HMS´ Anybus NetTool for Profibus, a powerful but easy to use Windows-based configuration tool which comes free with the X-gateway. After the initial configuration has been downloaded into the X-gateway, it passes up to 512 byte of input and 512 byte of output data transparently between Modbus-TCP and Profibus. Up to 124 Profibus slaves can be connected to the gateway. In addition to its data transfer capabilities, the X-gateway incorporates a powerful embedded web server on the Modbus-TCP side which supports web based remote diagnostics and visualization. Even an OPC server is included in the scope of delivery of the X-gateway. The X-gateway contains Profibus and Modbus-TCP communication interfaces that have been certified for full compliance to the respective protocol standards.

The Anybus X-gateway family is a product line consisting of over 200 proven, robust and ready-to-use gateways aimed to connect almost every possible combination of two industrial networks. The product family supports 17 different fieldbus and industrial Ethernet networks such as Profibus, DeviceNet, CANopen, CC-Link, EtherNet/IP, Profinet and many more. All versions work the same way and provide a flexible standard solution to connect two industrial networks.

Contact:

HMS Industrial Networks

Stationsgatan 37
30245 Halmstad
Sweden
Telephone : +46-351729-00
Fax : +46-351729-09
Email : min@hms.se
Web : www.anybus.com

Read More

Basic Electrical Installation Book

Basic Electrical Installation

PDF | 9MB
Download

Electrical Engineering Know it all

2008 / PDF / 7MB
Download

Read More