Tahukah anda, Apakah RSEmulator 5000?
RSEmulator 5000 adalah software yang dikeluarkan oleh Rockwell Automation untuk Simulasi PLC menggunakan software (internal PC). Software ini dilink dengan RSLogix 5000 menggunakan RSLinx.
Untuk jelasnya mendingan baca deh ..... Silahkan Klik DISINI!
Dibawah ini sedikit informasi mengenai RSEmulator.
--------------------
RSlogix Emulate 5000 ReadMe.txt File, 20-JAN-2007
*******************************************************
*WARNING: Do not depend on the emulator to match your *
*physical controller’s performance or operation. Some *
*instructions are interpreted differently in the *
*emulator than in a physical controller, and the *
*execution times for instructions and program files *
*will be significantly different in an emulated *
*controller than in a physical controller. *
*******************************************************
This readme file contains information on the following:
* System Requirements
* Product Revision Information
* Installation Procedure
* Technical Information
* Contact Information
System Requirements
Base Platform Requirements:
Intel Pentium 4 1.6GHz (single core, dual-core, and hyperthreaded CPUs are supported)
A minimum of 256 Mb of RAM
150 Mb of hard disk space free
800 X 600 video resolution
Any Windows-compatible pointing device
Operating System:
Microsoft Windows 2000 with Service Pack 4 (recommended)
Microsoft Windows XP with Service Pack 1 or higher (recommended)
Microsoft Windows 2003 Server
Product Revision Information
RSLogix Emulate 5000 Version 16.00.00 requires the following:
Software Product Compatible Versions:
RSLinx 2.51.00 or higher
Any RSLogix 5000 version from Version 12 through 16
Installation Procedure
Product Installation:
Begin the installation of the product by running the setup.exe file
located at the root of the CD media. This will launch a CD browser that
provides a means to install the RSLogix Emulate 5000 product, and
also displays pertinent product information.
Please use the "Add/Remove Programs" applet in control panel to remove
previous versions of SoftLogix5800. While performing an install or uninstall,
please note any messages that recommend a system reboot. Failure to follow
the reboot instructions can render your installation inoperable.
If you want to reinstall the same vesion as is currently installed, please use the
"Add/Remove Programs" applet in control panel to remove the existing version of
RSLogix Emulate 5000. While performing an install or uninstall, please note any
messages that recommend a system reboot. Failure to follow the reboot instructions
can render your installation inoperable.
Please refer to the RSLogix Emulate 5000 Getting Results Guide for details on
installing this product. This document can be viewed with the Adobe Acrobat
Reader by opening the file LGEM5K-GR016A-EN-P.pdf located at
IMPORTANT NOTES:
RSLogix Emulate 5000 cannot be installed on any machine that already has
SoftLogix5800 installed on it.
RSLinx Classic should be installed before installing the RSLogix Emulate 5000
product.
If RSLinx Classic is installed after RSLogix Emulate 5000, please run the
SIRegEDS.exe program that can be found in the RSEMU5000 directory on the
installation CD. After the products are installed, you must first add the
Virtual Backplane driver in RSLinx Classic in order to connect to the
SoftLogix engine.
Even if you plan to remotely program the controller over a ControlNet or
Ethernet link, you must add the Virtual Backplane driver via RSLinx Classic
software. If you do not, persistent storage will not function and when you
reboot the computer, the controller will come up with cleared memory (the
program will not get re-loaded).
Data Execution Prevention (a feature of Microsoft Windows also known as DEP) is
not supported by RSLogix Emulate 5000. If your computer's CPU supports DEP, we
advise using DEP for only essential Windows programs and services. (This is the
default setting for Windows XP; for Windows Server 2003, DEP is on by default
for all programs and services.) If DEP is turned on for RSLogix Emulate 5000,
you may experience unexpected results. See your Windows documentation for
information regarding DEP.
Jump to Subroutine (JSR) instructions do execute in the emulator. However,
the instruction passes parameters to subroutines in reverse order from the
order in a physical controller (the last parameter is passed first in an
emulated controller). Do not use JSR instructions in a manner where the
order in which parameters are passed to a subroutine matters.
Technical Information
Refer to the RSLogix Emulate 5000 Getting Results Guide for more information about using
this product. This document can be viewed with the Adobe Acrobat Reader by opening the
file LGEM5K-GR016A-EN-P.pdf located at
Emulate 5000 CD.
Contact Information
If you have any problems installing or running this software, please contact:
Rockwell Automation Technical Support
Phone: 440-646-5800
WEB: support.rockwellautomation.com
0 Comments:
Post a Comment